Top 10 typical forklift crashes ， forklift procedure must focus on these issues ！.

Don't undervalue the forklift at the office. If the operation is not good, there will certainly be severe accidents in minutes, and there are many mishaps entailing forklifts.

Instance 1: The forklift cargo blocked the motorist's view, and the individual in front can not be discovered, leading to a rolling accident.
Instance 2: In order to maintain the equilibrium of the forklift when raising hefty products, the employees used their body weight as the counterweight, which nearly triggered casualties.
Situation 3: The width of the forklift freight surpasses the allowed width of the route and holds on the roadside shelf, which almost causes an accident.
Case 4: Forklift is speeding and rolls over during a turn.
Case 5: The forklift chauffeur did not see the pedestrian, and the pedestrian did not observe the forklift.
Instance 6: The forklift raises the employees illegally, the forklift motorist does not use the seat belt, the forklift lifter drops and the motorist is squashed when the forklift rolls over.
Instance 7: The forklift chauffeur did not put on a seat belt and dropped from the car when it surrendered and was squashed.
Forklift operation should take note of these matters ：.

Begin.
1. Prior to starting, observe the environments, and after verifying that there are no obstacles that hinder the safety and security of driving, honk the horn initially and after that begin.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale have to be safe prior to starting.
3. When the forklift starts with a lots, the motorist should first validate that the load is secure and trusted.
4. The start must be sluggish and consistent.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground need to be maintained 300mm-400mm, and the pole should be slanted backward. .
2. Do not lift the fork expensive when driving. When entering and leaving the task site or while driving, beware that there will be no obstacles in the sky. When the load is traveling, the fork needs to not be elevated expensive, which will certainly influence the security of the forklift. .
3. After dumping, the fork needs to be lowered to the normal driving setting before driving. .
4. When turning, if there are pedestrians or lorries close by, the driving signal must be issued first. High-speed doglegs are restricted. High-speed sharp turns will certainly trigger the automobile to lose side security and tip over. .
5. When the forklift is downhill, it is strictly forbidden to turn off the fire and slide, and it is prohibited to brake unexpectedly while driving with lots unless there are unique situations.
6. When the forklift is running, it needs to follow the web traffic rules in the manufacturing facility and should keep a specific safety and security range from the vehicle in front. .
7. When the forklift is running, the load should be in the most affordable placement that does not hinder the driving, and the gantry should be effectively tilted back. The tons shall not be increased other than when piling or packing. .
8. The elevation of the lots should not obstruct the driver's sight. In special circumstances, when the product influences the forward vision, drive at a low rate when reversing.
9. It is restricted to turn on the ramp, neither to drive throughout the ramp. .
10. The secure driving rate of the forklift in the manufacturing facility location is 5 km/h, and it has to drive safely at a reduced rate when getting in the production workshop area. .
11. When the forklift is raised, lifted or driven, it is prohibited for workers to stand on the fork to hold products and play a balancing role. .
12. If problems are located, they will certainly be repaired and reported in a timely way, and they will never run with ailments or hide them.

loading and dumping.
1. When fork-loading items, the distance in between the two forks need to be readjusted as needed to make the load of the two forks balanced and not manipulated, and one side of the product must protest the shelf. .
2. It is restricted to work with a single fork or utilize a fork top or draw. In special situations, safety warning signs have to be set up to remind bordering pedestrians. .
3. In the process of loading and discharging things, the forklift needs to be braked with the brake. .
4. The speed of the lorry ought to be slow and stable. Beware not to roll the wheels on the dunnage, so as not to extend the rolled things and hurt individuals. .
5. When making use of a fork to fork the goods, the fork should be as deep as possible under the tons, and it needs to be kept in mind that the fork pointer must not touch other items or things. The load ought to be stabilized with minimal back tilt of the gantry so that the lots does not glide in reverse. The mast can be slanted onward somewhat when the lots is decreased to permit simple positioning of the load and extraction of the forks. .
6. It is forbidden to fork items at broadband and collide with difficult items with the fork head. .
7. When the forklift is working, it is prohibited for people to loaf the fork, so regarding stay clear of the collapse of the goods and hurt people. .
8. Overwhelming is prohibited, and it is banned to use forks to lift personnel to engage in high-altitude procedures to stay clear of high-altitude falling crashes. .
9. It is not enabled to make use of the brake inertia to slide, place, round or roll things. .
10. It is not permitted to make use of forks to select, transform pallet unload.

Leaving .
1. It is restricted to leave the forklift when the things on the fork are in the air. Prior to leaving the forklift, you need to dump the goods or lower the fork structure.
2. Pull the emergency brake deal with to dead or depress the hand brake button.
3. The engine is shut off and the power is removed. (Except for unique circumstances, such as the driver does not leave the car's line of Stand-on Electric Pallet Stacker vision and does not surpass 1 minute).
4. Eliminate the key. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance needs to be examined, and gas, lubing oil and air conditioning water ought to be added.
2. Check the safety efficiency of beginning, running and stopping.
3. Inspect whether the lights and horn signals are complete and effective.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature level are regular.
5. After the forklift is running, the outside leakage should additionally be examined and Electric Forklift Truck for Warehouse the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine prior to leaving the automobile;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the cargo must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the propensity of "free switching";.
6. Running up and down the incline ought to be slow and consistent, and no turning on the incline is allowed.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the lorry must be driven backwards when declining;.
8. When the forklift personnel bring the goods and move forward, if they run into large or hefty goods and most likely to the driver's line of vision, they should take the reversing workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not permitted to bring individuals to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Parking is not permitted under the following conditions.
1. Contours, slim roadways, train crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an barrier on one side of the roadway, the contrary side of the area with the same length as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844